CL4000 - Glass Door Installation Instructions

CL4000 - Glass Door Installation Instructions

Box Contents

Check the contents of the box are correct

1Front Plate
2Lever handles x 2
3Inside lever boss
4Spindle + space
5Front patch fitting (LH or RH)
62 piece internal latch patch fitting (with gasket)
7Batteries x 4 'N cell'
8Front plate cylinder keys
9Through fixing allen bolts x 2 (short)
10  Patch fixing allen bolts x 2 (short)
11  Internal patch steel cover plate
12  Strike plate
13  Allen keys
14  Front plate cylinder cover
15  Classroom function tailpiece


This box should also contain Programming and Operating Instructions.

 

Tools Required

  • Philips screwdriver

Installation of Glass Door Lock

You should familiarise yourself with the lock  and its operation before attempting to fit. Locks are supplied as either RH or LH versions check  you have the correct product to suit the hand  of your door. Illustration page 5 shows RH version.

1. With digital lock face down on a bench remove the transit strip from the rear of the lock by removing the two transit screws.

2. Install batteries into lock ensuring that the positive and negative ends are correctly orientated.

3. Ensure that the clutch below the battery holder is in the correct position with orange and black cable exiting the top left of the clutch. If not rotate into the correct position.

4. Fit the front patch fitting to the frontplate with the two short transit bolts and tighten. Note – ensure cables are not trapped.

5. Test the factory master code by pressing 1234. The blue light should signal to show a correct code. The red light will signal after 5 seconds to show the code operation period has expired.

6. Fit the lever handle to the frontplate boss according to the hand of your door and secure with grub screw.

7. Remove the steel coverplate from the latch patch fitting by unthreading the Nylon nut.

8. Ensure that the latch patch fitting is handed to suit your door. The hand can be changed by a combination of reversing the latch head (via the securing screw) and/or by turning the latch patch fitting 180 degrees.

9. The spindle supplied is suitable for glass doors up to 15mm (9⁄16”) thick. For doors thicker than 15mm (9⁄16”) please install the spacer piece provided onto the long end of the spindle.  Now take the internal latch patch fitting and the spindle through the latch follower with the short end facing the code side. Push the spindle through until the washer rests against the patch lock.

10. Place the thin plastic gasket on the latch patch fitting so it is seated against the glass door and latch when assembled.

11. Holding latch patch fitting in place take the frontplate assembly and fit over spindle.

12. Using the 2 through fixing bolts from the latch side secure the code side and latch side together, ensuring the lock is aligned vertically and horizontally with the door.

13. Refit the steel coverplate to the latch patch fitting and secure with Nylon nut.

14. Take the internal lever boss and fit, pushing firmly onto spindle. Secure with grub screw.

15. Fit internal lever onto boss according to hand of door and secure with grub screw.

 

Operation Check

A) Enter the mastercode wait for the blue light and depress the lever which should retract the latch. After the red light depress the lever once more which should not retract the latch.
B) Depress the internal lever which should retract the latch.

A) or B) do not work please check installation from step 12 and that lock has not been set in passage function by key (see programming instructions).


NOW - Change factory set Mastercode (see programming instructions).

 

 

II/4kGD-0910

  © 2019 Codelocks Ltd.  All rights reserved.


    • Related Articles

    • CL4000 - Glass Door Installation Instructions

      Operations Check Factory Set Master Codes CL4000: 1234 CL4500: #12345678 A) According to your lock model, enter the Master Code, wait for the Blue LED to flash and depress the lever which should retract the latch. After the Red LED flash, depress the ...
    • CL4500 - Glass Door Installation Instructions

      Notice: The C3 Smart App replaced the K3 Connect App on February 14, 2023. For more information on how to download, set up and use C3 Smart with your Codelocks Smart Locks, visit: c3smart.net or contact Codelocks Support. Operations Check Factory Set ...
    • CL4500 - Glass Door Installation Instructions

      Operations Check Factory Set Master Codes CL4000: 1234 CL4500: #12345678 A) According to your lock model, enter the Master Code, wait for the Blue LED to flash and depress the lever which should retract the latch. After the Red LED flash, depress the ...
    • KitLock Slam Latch - Installation Instructions

      Suitable for use with the KitLock KL1000 family: KL1000 Classic, KL1000 Classic+, KL1000 G3, KL1000 G3 NetCode, KL1000 NetCode, KL1000 RFID. SPECIAL NOTE The maximum door thickness when using the Slam Latch is 20mm (3/4”). Before installation, ...
    • KL1100 RFID - Installation Instructions & Template

      INSTALLATION Please read carefully: Before installing the lock, read the programming and operating instructions suited to your KL1100 model. Please note, the KL1100 RFID requires a Master Card to be assigned on powering up. Instructions can be found ...