KL1500 - Installation Instructions

KL1500 - Installation Instructions

Special Notes

  • Please read carefully:
  • Before installing the lock, install the batteries and familiarise yourself with the operation and programming.
  • The handle will not turn until you enter the factory default code:
  • Master Code 11 22 33 44 or the User Code 12 34.
  • Please see Programming Guide to set your new Master and User Codes and to set different functions on lock if required.
  • If required change keypad orientation.
  • Select and fit coloured insertwith double sided tape supplied.

 

Fitting Instructions

The KL1500 is supplied for vertical installation. However, the lock may be installed in any orientation by simply rotating the keypad module.
Before installation change to desired orientation as follows:

 

1. Remove both batteries.

2. Remove lever handle via handle fixing boltfrom rear of lock.

3. Remove four small fixing bolts.

4. Carefully remove the outer lock shell.

5. Rotate the numeric module(1-9) to the required position.

6. Replace the outer lock shelland secure with the 4 small fixing bolts.

7. Press and hold the button and replace one battery. The blue LED will flash twice and the lock will beep twice.

8. Release the button and within three seconds press the * button 3 times.

9. The blue LED will flash twice and will beep twice to confirm numeric module position reset OK.

10. Replace the handleand fit second battery.

 

 

 

The KitLock can be fitted to:​
Cabinets, cupboards and lockers etc.as a direct replacement for existing cam locks.

It can also be fitted easily to cupboards and cabinets that do not have an existing locking device.

 

Installation Guide

A. Replace existing cam lock with the KitLock

Step 1 Remove existing cam lock.

Step 2 Place the template over the hole left by the cam lock and mark the upper and lower fixing holes.

Step 3 Drill the two 6mm (1⁄4”) fixing holes.

Step 4 Fit lock to door with gasket in place using fixing bolts. Cut bolts to correct length. Measured from beneath the bolt head, the length should be the cabinet thickness, plus approx 12mm (1⁄2”).

Step 5 From the inside of the door select and fit appropriate cam spindle and cam using cam fixing bolt supplied.  The length of cam and spindle selected to suit your door and frame.

Step 6 Before closing the door check the operation of the lock with Master and User Code.

Step 7 If not changed already CHANGE FACTORY SET MASTER AND USER CODE NOW.

Step 8 If not already fitted, select and fit coloured insert

 

B. New Installation

Step 1 Place template on door and mark upper and lower 6mm (1⁄4") fixing holes and 16mm (5⁄8”) spindle hole.
Note: Before drilling fixing holes, please ensure the position of the KitLock when fitted will allow enough clearance for selected cam to work.

Step 2 Drill all three fixing holes.

Step 3 Continue installation from Step 4 to 8 from the Installation Guide (Section A).

 

II-KL1500-v2:0613

  © 2019 Codelocks Ltd.  All rights reserved.

    • Related Articles

    • KitLock Slam Latch - Installation Instructions

      Suitable for use with the KitLock KL1000 family: KL1000 Classic, KL1000 Classic+, KL1000 G3, KL1000 G3 NetCode, KL1000 NetCode, KL1000 RFID. SPECIAL NOTE The maximum door thickness when using the Slam Latch is 20mm (3/4”). Before installation, ...
    • KL1100 RFID - Installation Instructions & Template

      INSTALLATION Please read carefully: Before installing the lock, read the programming and operating instructions suited to your KL1100 model. Please note, the KL1100 RFID requires a Master Card to be assigned on powering up. Instructions can be found ...
    • KL1100 KeyPad - Installation Instructions & Template

      INSTALLATION Please read carefully: Before installing the lock, read the programming and operating instructions suited to your KL1100 model. Please note, the KL1100 RFID requires a Master Card to be assigned on powering up. Instructions can be found ...
    • KL1100 RFID - Programming and Operating Instructions

      ABOUT KL1100 RFID The KL1100 RFID can operate in Standalone Mode or in Remote Card Authorisation (RCA) Mode. RCA Mode gives the ability to remotely set-up and allocate cards to locks or lock groups  with our offline or cloud based software. ...
    • CL5500 - Programming and Operating Instructions

      Notice: The C3 Smart App replaced the K3 Connect App on February 14, 2023. For more information on how to download, set up and use C3 Smart with your Codelocks Smart Locks, visit: c3smart.net or contact Codelocks Support . About CL5500 The CL4500 and ...