KL1000 NetCode - Getting Started Installation Instructions and Quick Start Guide

KL1000 NetCode - Getting Started Installation Instructions and Quick Start Guide


The KL1000 NetCode supports date/time sensitive NetCodes which can be generated via the NetCode Portal.  You must have access to a browser with internet access to set-up NetCode.

 

Special Notes

Please read carefully:

  • Before installing the lock, load the batteries and familiarise yourself with the operation and programming.
  • The handle will not turn until you enter the factory default Master Code 11335577 or the User Code 2244.
  • Visit www.codelocksportal.net to proceed with the set-up. Note that you will need to register for an account if you do not already have one.
  • Once signed-in, choose Add Lock. As part of the initialisation process, you will be given a program string to enter into your lock. When displayed, this should be entered immediately.
  • Your KitLock is supplied ready to fit to doors up to 19mm (3⁄4") thick. For doors between 19mm (3⁄4") and 25mm (1") thick, you will need to install the 28.5mm (1 1⁄8") spare spindle (see below). A 12mm (1⁄2") spindle is also included for sheet metal doors.

 

Public & Private Functions

Although the KL1000 NetCode is intended as a NetCode lock, the KL1000 NetCode does support traditional Public & Private Functions. Documentation for these functions can be found at www.support.codelocks.com

 

Factory Reset

You may need to reset your lock to factory settings if you want to re-register the lock on the NetCode Portal or have forgotten the Master Code.

  1. Remove the rear-fixing bolt and swing the lock over the edge of the door to reveal the battery compartment.
  2. Remove one battery.
  3. Press and hold the 1 button.
  4. Replace the battery whilst continuing to hold the 1 button. The Blue LED will flash twice.
  5. Release the 1 button.
  6. Within three seconds, press the 1 button three times. The Blue LED will flash three times and the lock will have reverted to factory settings. The Master Code will now be 11335577, the lock will be in Private Function and the User Code will be 2244. All other settings will be erased and reset.

 

Installation Guide Steps

KL1000 NetCode can be fitted to:

A. Cabinets, cupboards and lockers etc. as a direct replacement for existing cam locks.

B. It can also be fitted easily to cupboards and cabinets that do not have an existing locking device.

KL1000 NetCode can be supplied vertically and left or right hand horizontal.


 

A. Replace existing cam lock with KL1000 NetCode

  1. Remove existing cam lock.
  2. Place the 16mm (5⁄8") template hole over the hole left by the cam lock and mark the upper fixing hole.
  3. Drill the 6mm (1⁄4") fixing hole.
  4. Fit the KitLock to the door by passing the spindle through the 16mm (5⁄8") hole.
  5. If required, from the inside of the door, pass either of the packing pieces over the spindle to centralise the lock.
  6. Now secure the lock by threading the large nut onto the spindle.
  7. Fit one of the upper fixing bolts to suit your door thickness.
  8. Tighten the lower fixing nut and upper bolt.
  9. Select the cam which suits your door and frame and attach it to the square shaft at the end of the spindle.
  10. Now check the operation of the lock using the factory User Code 2244.
  11. If the lock is functioning correctly, CHANGE THE DEFAULT MASTER CODE 11335577 AND DEFAULT USER CODE 2244 and program the lock using the programming and operating instructions found at www.support.codelocks.com

 

B. New Installation

  1. Place template on door and mark upper 6mm (1⁄4") hole and lower 16mm (5⁄8") hole.
    IMPORTANT NOTE: Before drilling fixing holes, please ensure the position of the KitLock when fitted will allow enough clearance for selected cam to work.
  2. Drill both fixing holes.
  3. Continue to installation from 4 to 11 above.

 

GSII-KL1060NC-v2:0416

 

© 2018 Codelocks Ltd.  All rights reserved.

 


    • Related Articles

    • KL1100 RFID - Getting Started Guide

      ABOUT KL1100 RFID The KL1100 RFID can operate in Standalone Mode or in Remote Card Authorisation (RCA) Mode. RCA Mode gives the ability to remotely set-up and allocate cards to locks or lock groups with our offline or cloud based software. This ...
    • CL4500 - Getting Started Guide

        About CL4500 This range of locks can be operated and managed directly via the keypad or via a compatible smartphone by downloading the K3 Connect App. This Getting Started guide contains the common functions to enable you to quickly program your ...
    • CL5510 - Getting Started Guide

      This range of locks can be operated and managed directly via the keypad or via a compatible smartphone by downloading the K3 Connect App.                                This Getting Started guide contains the common functions to enable you to quickly ...
    • KL1550 - Getting Started Installation Instructions

      The KL1550 SMART is a multi-purpose locker lock that supports Public and Private Use, MIFARE based smart cards and NetCode. Programming can be by traditional keypad entry or by a tablet sold separately.   Special Notes Please read carefully: • Before ...
    • KL1000 G3 NetCode - Getting Started Guide

      Before use, two AAA batteries must be fitted by rotating the handle, removing the security screw with the star drive tool provided and sliding the top cover away from the handle. The KL0000 G3 NetCode is supplied with a factory set Master Code ...