KL1000 Classic - 2014 Right Hand Programming & Operating Instructions 04/14 >

KL1000 Classic - 2014 Right Hand Programming & Operating Instructions 04/14 >

Codes - The Basics

  • The KitLock has four code levels available:

    1. Master Code

    2. Sub-Master Code

    3. User Code

    4. Technician Code

  • The KitLock is supplied with two factory set codes:

    1. Master Code: 55 44 33 22

    2. User Code: 00 99

  • When fitted immediately change the Master Code and User Code.

  • All Master Codes and Sub-Master Codes are 8 digits long.

  • All User Codes are 4 digits long.

  • All Technician Code are 6 digits long.

  • The lock ‘open’ time is set at 4 seconds.

 

Functions

Before programming, select the most appropriate function for the application: A) or B) – See special Master Code set up commands.

A) PRIVATE USE

Important Note: This is the default function and is already pre-programmed in new locks. This is the most common function and is used where the same code will be repeatedly used.

B) PUBLIC USE

The user enters their own personal four-digit code. This locks the lock. The same code is entered once only to open the lock before being erased and ready for the next new user. This function is used for short term, multi occupancy applications, e.g. a locker in a leisure centre.

 

Operating Instructions

Note: The KitLock has a 10 button keypad and a # button. The # button is hidden beneath the handle when in the locked position. The lock has the following code levels:

Master Code can:

  • Open the lock

  • Change the Master Code

  • Set / Change / Delete the Sub-Master and User Code

  • Select between repeated use and single use codes

  • Activate/deactivate technician mode

Sub-Master Code can:

  • Open the lock

  • Change the Sub-Master

  • Set / Change / Delete / the User Code

User Code can:

  • Open the lock

  • Change the User Code

Technician Code can:

  • Open the lock. A code cannot be programmed into more than one level.

 Lost Code Procedure

Note: The procedure requires the door to be open

• Remove the rear-fixing bolt and swing the lock over the edge of the door to reveal the battery compartment.

• Remove one battery.

• Press and hold the 5 button, replace the battery, the blue LED will flash twice, release the 5 button. Within three seconds press the 5 button three times. The blue LED will flash twice and the lock will have reverted to the factory master code 55 44 33 22 and all other stored settings will be erased.

Penalty time

• Entering three incorrect codes will cause the lock into shutdown for 10 seconds.

Battery Power

The KitLock should provide well in excess of 15,000 openings, of 4 seconds each, from 2 x AAA 1.5v cells.

Low Battery

When the battery power is low the Red LED will flash 3 times before the Blue LED flashes to signal acceptance of the code. Batteries should be changed as soon as this happens. The lock will operate for 100 times with low battery.

 

 

MASTER CODE COMMANDS

  • Change the MASTER CODE

    • #Master Code  65  New Master Code • New Master Code ••

    • Example: #55443322  65  12345678  12345678 ••

    • Result: Master Code has been changed to 12345678.

  • Set or change the USER CODE

    • #Master Code  60  User Code ••

    • Example: #55443322  60  9999 ••

    • Result: New User Code 9999 now operative.

  • Delete USER CODE

    • #Master Code • 64 ••

    • Example:#55443322  64 ••

    • Result: User Code deleted.

  • Set or change che SUB-MASTER CODE

    • #Master Code  69  Sub-Master Code  Sub-Master Code ••

    • Example: #55443322  69  87654321  87654321 ••

    • Result: Sub-Master Code 87654321 now operative.

  • Delete SUB-MASTER CODE

    • #Master Code  63  63 ••

    • Example: #55443322  63  63 ••

    • Result: Sub-Master Code deleted.

 

SUB-MASTER CODE COMMANDS

  • Change the SUB-MASTER CODE

    • #Sub-Master Code  68  New Sub-Master Code  New Sub-Master Code ••

    • Example: #87654321  68  10101010  10101010 ••

    • Result: Sub-MasterCode has been changed to 10101010.

  • Set or Change the USER CODE

    • #Sub-Master Code  62  User Code ••

    • Example: #87654321  62  6666 ••

    • Result: New User Code 6666 now operative.

  • Delete USER CODE

    • #Sub-Master Code  67 ••

    • Example: #87654321  67 ••

    • Result: User Code deleted.

 

USER CODE COMMANDS

  • Change the USER CODE

    • #User Code  New User Code • New User Code ••

    • Example: #0099  6688  6688 ••

    • Result: User Code now 6688.

 

SPECIAL MASTER CODE COMMANDS

  • Set PRIVATE USE
    • #Master Code  08 ••
    • Example: #55443322  08 ••
    • Result: The lock will revert back to default function A) repeated use. Factory set User Code 0099 will now work repeatedly until programmed.

 

  • Set PUBLIC USE – SINGLE CODE ENTRY (DEFAULT)
    • #Master Code  09 ••
    • Example: #55443322  09 ••
    • Result: The lock will now remain open until the next single use code is entered into the lock as follows:
      1. Enter 4 digit code  Close the locker which will now be locked
      2. Enter the same 4 digit code •• the lock will now open and remain open until next 4 digit code is entered

 

  • Set PUBLIC USE – DOUBLE CODE ENTRY
    • #Master Code  00 ••
    • Example: #55443322  00 ••
    • Result: The lock will now remain open until the next single use code is entered into the lock as follows:
      1. Enter 4 digit code  Repeat 4 digit code •• Close the locker which will now be locked
      2. Enter the same 4 digit code •• the lock will now open and remain open until next 4 digit code is entered as Step 1
    • Note: When locked in this mode  LED will flash every 5 seconds to indicate the locker is locked.

 

  • Set TECHNICIAN CODE
    • #Master Code  11  Technician Code  Technician Code ••
    • Example: #55443322  11  555555  555555 ••
    • Result: The lock is automatically set into function B) single use Locker Mode AND allows the programmed Technician Code to open the lock WITHOUT the entered single use code being erased.
    • Note: If lock is opened with a Master Code the User Code will be erased.

 

 

POI_KL1000RH-V20214

 © 2019 Codelocks Ltd.  All rights reserved.
    • Related Articles

    • KL1000 Classic Programming and Operating Instructions [GB]

      CODES - THE BASICS The KitLock has four code levels available: Master Code Sub-Master Code User Code Technician Code The KitLock is supplied with two factory set codes: Master Code: 11335577 User Code: 2244 When fitted, immediately change the Master ...
    • KL1200 - Right Hand Programming & Operating Instructions

      Codes - The Basics The KitLock has four code levels available: Master Code Sub-Master Code User Code Technician Code The KitLock is supplied with two factory set codes: Master Code: 55 44 33 22 User Code: 00 99 When fitted immediately change the ...
    • KL1000 Classic+ - Programming and Operating Instructions

      IMPORTANT: This guide is for the KL1000 Classic+ model. The standard KL1000 Classic Programming and Operating Instructions are available here. The KL1000 Classic+ is a compact digital lock based on the venerable KL1000 Classic, with the additional ...
    • KL1000 Classic - 2014 Right Hand Programming & Operating Instructions

      Codes - The Basics The KitLock has four code levels available: Master Code Sub-Master Code User Code Technician Code The KitLock is supplied with two factory set codes: Master Code: 55 44 33 22 User Code: 00 99 When fitted immediately change the ...
    • KL1000 Classic - Pre 2013 Right Hand Programming & Operating Instructions

      Codes - The Basics The KitLock has four code levels available:got Master Code Sub-Master Code User Code Technician Code The KitLock is supplied with two factory set codes: Master Code: 55 44 33 22  User Code: 00 99 When fitted immediately change the ...