CL2210 - Mortice Deadbolt Installation Instructions

CL2210 - Mortice Deadbolt Installation Instructions

Installation Instructions for the CL2210 Mortice Deadbolt

 

Contents

 

 

CL2210

1

Front plate

(tick)

2

Back plate

(tick)

3

Neoprene seals x 2

(tick)

4

Spring loaded spindle

(tick)

5

Deadbolt 60mm and 70mm, (2  3⁄8" - 2 3⁄4") backset  

(tick)

6

Keeper plate

(tick)

7

Wood screws x 4 use with deadbolt support post

(tick)

8

Deadbolt support post

(tick)

9

Fixing bolts 3 supplied (spare x1)

(tick)

10

2 keys

(tick)

11

Cable Connections for REM1 and REM2

(tick)

12

1.5v AA Batteries (x2)

(tick)

 

 

Tools required for installation

  • Power drill
  • 20mm (25⁄32") , 25mm (1"), 15mm (1⁄2") & 8mm (5⁄16")drill bits
  • Bradawl
  • Phillips screwdriver size 2
  • Chisel - maximum 25mm (1")
  • Hammer/Mallet
  • Stanley knife
  • Adhesive tape
  • Pencil
  • Tape measure

 

Mortice Latchset 

 

Special Notes

You are advised to familiarise yourself with the instructions before starting work.

  • Remove the battery cover from the back plate and install the 2 x AA cells supplied.
  • Connect the cables from the front plate and back plate. A BLEEP should be heard when you do this. If no BLEEP is heard then check that the batteries are correctly installed.
  • Enter the factory Master Code, 1234 (not: when programming the badge bar must prefix the Master Code).
    The blue LED will flash and the front knob can be turned using finger and thumb.
  • Disconnect the cables.
  • Check that the deadbolt moves freely by turning the flat spindle in the cam.

 

1. Check the hand of your door

 

Viewed from outside, a door is right handed if the hinges are on the right, and left handed if the hinges are on the left.

 

2. Apply the template

  • Crease the template along the line marked Door Edge, using either the 60mm (2 3⁄8") or 70mm (2  3⁄4") backset line and tape it to the door.
  • Mark the 2 x 8mm (5⁄16"), 4 x 15mm (5⁄8") holes and the 20mm (2  5⁄32") hole. Mark the centre line of the deadbolt in the middle of door edge. Now apply the template to the other side of the door, aligning it with your first mark in the middle of the door edge. Mark the 7 holes again.
  • Keeping the drill level and square to the door, drill holes from both sides to avoid splintering out of door face.

Positioning and fixing the deadbolt

  • Mark a central point on the 'centre line of deadbolt' on the door edge.
  • Mark the depth of 90mm (3 1⁄2") on the drill bit with tape to act as a visible depth limit. Drill a 25mm (1") hole, 90mm (3  1⁄2") deep, keeping the drill level and square to the door.
  • Insert the deadbolt into the hole, and with the edges parallel to the door, draw around the face plate.
  • Remove the deadbolt. Score the pencil line with a Stanley Knife to avoid splitting prior to chiselling. Chisel a 3mm (1⁄8") rebate to fit the deadbolt face flush to the door edge.
  • Fix the deadbolt with the wood screws, with the arrow pointing up.

3. Deadbolt support post

4. Positioning the spindle

  • For doors more than 65mm (2 1⁄2") thick, ring the Helpline for advice. The spring keeps the spindle firmly engaged in the outside handle when the lock is assembled on the door.
  • Insert the spindle, with the spring on the code side, through the slot in the deadbolt.

 

5. Fixing the lock

  • Cut the fixing bolts to suit the door thickness, allowing at least one, but no more than two, threaded sections to enter the lock case.
  • Remove the battery cover from the back plate, and remove the battery pack. Apply the front plate over the spindle, if using the 60mm backset pass the deadbolt support post through the deadbolt and the cable through the door. Place the back plate over the spindle, pull the cable through, and screw the fixing bolts through to the front plate.
  • Using the inside knob check that the spindle moves freely, and that the deadbolt retracts and projects smoothly. If it is tight, loosen the fixing bolts slightly and adjust the position of the backplate until the spindle will turn freely. Tighten the fixing bolts. Test the spindle again. DO NOT over-tighten the bolts as this may cause the door to distort and affect the lock function.

DO NOT CLOSE THE DOOR UNTIL YOU ARE SURE THAT THE CODE WORKS

  • Connect the cables, storing any excess cable within the door. Then install the battery pack.

 

6. Fixing the keeper plate

  • Position the keeper plate on the frame so that it lines up with the deadbolt.
  • Mark the inner and outer edges of the keeper plate and cut a rebate so that it fits flush with the surface of the door frame.
  • Drill or cut a recess 25mm (1") deep for the deadbolt.
  • Fit the keeper plate using only one wood screw at first to ensure that it is positioned accurately. The deadbolt should enter the aperture easily. When satisfied secure the keeper with the second screw.

 

II-2K-0812-V01

 © 2019 Codelocks Ltd.  All rights reserved.
    • Related Articles

    • CL210 - Mortice Deadbolt Installation Instructions

      Contents 1 Front plate (key override option shown) 2 Back plate 3 Neoprene seals x 2 4 Spring loaded spindle 5 Deadbolt - 60mm (2 3⁄8”) backset 6 Keeper plate 7 Wood screws x 4 Use with deadbolt & keeper plate 8 Deadbolt support post 9 Tweezers (for ...
    • CL300 - Mortice Deadbolt Installation Instructions

      Contents 1 Front plate with key override 2 Back plate 3 Gaskets x 2 4 Spring loaded spindle 5 Deadbolt 60mm (2 3⁄8”) and 70mm (2 3⁄4” ) backset x3 6 Strike plate 7 Wood screws x 6 (use with latch & strike plate) 8 Tweezers (for changing the code) 9 ...
    • KitLock Slam Latch - Installation Instructions

      Suitable for use with the KitLock KL1000 family: KL1000 Classic, KL1000 Classic+, KL1000 G3, KL1000 G3 NetCode, KL1000 NetCode, KL1000 RFID. SPECIAL NOTE The maximum door thickness when using the Slam Latch is 20mm (3/4”). Before installation, ...
    • CL2200 - Surface Deadbolt Installation Instructions

      Installation Instructions for the CL2200 Surface Deadbolt Contents     CL2200 1 Front plate 2 Back plate 3 Neoprene seals x 2 4 Spring loaded spindle 5 Mortice Keeper 6 Surface keeper and packing pieces 7 Wood screws x 2 (to use with keeper) 8 Fixing ...
    • CL100/CL200 - 2015 Surface Deadbolt Installation Instructions

           Contents Special Notes Before commencing installation check that all parts are working correctly. Press the code according to the code card and the knob should then turn, in either directions, once only, and return easily under spring pressure. ...