CL2200 - Surface Deadbolt Installation Instructions

CL2200 - Surface Deadbolt Installation Instructions

Installation Instructions for the CL2200 Surface Deadbolt

Contents

 

 

CL2200

1

Front plate

(tick)

2

Back plate

(tick)

3

Neoprene seals x 2

(tick)

4

Spring loaded spindle

(tick)

5

Mortice Keeper

(tick)

6

Surface keeper and packing pieces

(tick)

7

Wood screws x 2 (to use with keeper)

(tick)

8

Fixing bolts 3 supplied (spare x 1)

(tick)

9

2 keys

(tick)

10

Cable Connections for REM1 and REM2

(tick)

11

1.5v AA Batteries (x2)

(tick)

 

Tools required for installation

  • Power drill
  • 25mm (1") , 13mm (1⁄2"), 8mm (5⁄16") drill bits
  • Bradawl
  • Phillips screwdriver size 2
  • Chisel - maximum 25mm (1")
  • Hammer/Mallet
  • Stanley knife
  • Adhesive tape
  • Pencil
  • Tape measure

 

 

 

Special Notes

You are advised to familiarise yourself with the instructions before starting work.

  • Install the 2 x AA cells supplied into front plate.
  • A BLEEP should be heard when you do this. If no BLEEP is heard then check that the batteries are correctly installed.
  • Enter the factory Master Code, 1234 (note: when programming the badge bar  must prefix the Master Code). The blue LED will flash and the front knob will can be turned using finger and thumb.
  • After installation change factory set Master and User Codes - see programming instructions provided.

 

1. Check the hand of your door

  • Your door is right-handed if, viewed from outside, the hinges are on the right.

 

2. Positioning the lock

  • Remove the inside cover plate from the back plate, and install the deadbolt according to the hand of your door. Note that the standard bolt
    projects 40mm (1 9⁄16") to the locking side. A shorter bolt which projects 20mm (3⁄4") is available.
  • Set the back plate with the knob in the vertical position and hold it to the door with one end of the bolt against the frame where the keeper will be fitted (see step 4).
  • Mark the position of the top fixing hole for the spindle. Drill 8mm (5⁄16") holes for fixing bolts and 13mm (1⁄2") hole for spindle.

 

3. Fixing the lock

  • Cut the fixing bolts to suit the door thickness, length of bolts measured beneath the bolt head should be door thickness plus 15mm (5⁄8").
  • Using the inside knob check that the spindle moves freely, and that the latch retracts and projects smoothly. If it is tight, loosen the fixing bolts slightly and adjust the position of the back plate until the spindle will turn freely. Tighten the fixing bolts. Test the spindle again. DO NOT over tighten the bolts as this may cause the door to distort and affect the lock function.

DO NOT CLOSE THE DOOR UNTIL YOU ARE SURE THAT THE CODE WORKS 

 

4. Fitting the keeper

  • First select the appropriate keeper for your frame.
  • Position the keeper on the frame so that it lines up with the deadbolt and mark the appropriate holes.
  • If you are using the Surface Keeper simply screw into place (see fig. 5.1). Use the packaging pieces as required.
  • The Mortice Keeper will require cutting a small recess (see fig. 5.2)

 

II-2000-SD-0810

  © 2019 Codelocks Ltd.  All rights reserved.

    • Related Articles

    • CL100/CL200 - 2015 Surface Deadbolt Installation Instructions

           Contents Special Notes Before commencing installation check that all parts are working correctly. Press the code according to the code card and the knob should then turn, in either directions, once only, and return easily under spring pressure. ...
    • CL100/CL200 - 2018 Surface Deadbolt Installation Instructions

      CONTENTS     CL100  CL200  1 Front Plate (Key override option shown) 2 Back plate (bolt is packed separately) 3 Neoprene seals x 2  4 Packaging pieces x 2 5  Spring loaded spindle 6 Mortice keeper 7 Surface keeper 8 Surface keeper packing pieces x 1 ...
    • CL100/CL200 - 2018 Surface Deadbolt Installation Instructions

        CONTENTS     CL100  CL200  1 Front Plate (Key override option shown) 2 Back plate (bolt is packed separately) 3 Neoprene seals x 2  4 Packaging pieces x 2 5  Spring loaded spindle 6 Mortice keeper 7 Surface keeper 8 Surface keeper packing pieces x ...
    • CL2210 - Mortice Deadbolt Installation Instructions

      Installation Instructions for the CL2210 Mortice Deadbolt   Contents     CL2210 1 Front plate 2 Back plate 3 Neoprene seals x 2 4 Spring loaded spindle 5 Deadbolt 60mm and 70mm, (2  3⁄8" - 2 3⁄4") backset   6 Keeper plate 7 Wood screws x 4 use with ...
    • CL210 - Mortice Deadbolt Installation Instructions

      Contents 1 Front plate (key override option shown)                      2 Back plate                                                                     3 Neoprene seals x 2                                                        4 Spring loaded ...