CL100/CL200 - 2015 Surface Deadbolt Installation Instructions

CL100/CL200 - 2015 Surface Deadbolt Installation Instructions

    

Contents

Special Notes

Before commencing installation check that all parts are working correctly. Press the code according to the code card and the knob should then turn, in either directions, once only, and return easily under spring pressure. From inside the door the bolt can be freely locked and unlocked using the knob. From outside the code is required both to lock and to unlock the bolt. If you would like to be able to LOCK your door from outside WITHOUT using the code then follow instructions 2.

  • If you intend to change the code then, if it is convenient, you should do it before installing the lock. See the code change instructions in the separate leaflet.

  • Note that the lock is supplied as standard with a bolt which projects 40mm from the side of the lock. A shorter bolt which projects 20mm is available.

 

1.Check the hand of your door

Your door is right-handed if, viewed from the outside, the hinges are on the right.

 

2.Outside knob locking action

To enable LOCKING of the bolt from outside WITHOUT using the code:

  • Press the C button to reset the chamber and place the lock case on a flat surface with the buttons down.
  • Remove the code chamber plate held in place with the two red screws.
  • With the tweezers remove the right-hand pin for right-handed doors, or the left-hand pin for left-handed doors.
  • Replace the cover plate.
  • The outside knob will now feel loose and turn freely in one direction, and will require the code to be used before it will turn in the other direction.
    NB: When installing the lock make sure that the driver is in the correct position before installing the spindle.

 

3.Positioning the lock

  • Remove the inside cover plate from the back plate, and install the deadbolt according to the hand of your door. Note that the standard bolt projects 40mm to the locking side. A shorter bolt which projects 20mm is available.
  • Set the back plate with the knob in the vertical position and hold it to the door with one end of the bolt against the frame where the keeper will be fitted (see step 5).
  • Mark the position of the top fixing hole, and then using one of the packing pieces as a template mark the position of the lower fixing hole and the hole for the spindle.

 

4.Fixing the lock

  • The spring loaded spindle will fit doors between 35mm and 65mm thick. For doors less than 50mm thick break off the 15mm section at the end of the spindle. For doors more than 65mm thick ring the helpline for advice. The spring keeps the spindle firmly engaged in the outside handle when the lock is assembled on the door.
  • Cut the fixing bolts to suit the door thickness, allowing for the rubber seals and at least one threaded section to screw into the lock case. Note that the bottom fixing bolt will be longer than the top.
  • Hold the lock case and the back plate, with the neoprene seals in place, onto the door with the spindle in position. Using the top fixing bolt screw everything together.

 

5.Fitting the keeper

 

  • First select the appropriate keeper for your frame.
  • Position the keeper on the frame so that it lines up with the deadbolt and mark the appropriate holes.
  • If you are using the Surface Keeper simply screw into place (see fig. 5.1). Use the packing pieces as required.
  • The Mortice Keeper will require cutting a small recess (see fig. 5.2).

 

 

II-CL100/200SD-v2:07172

  © 2019 Codelocks Ltd.  All rights reserved.

    • Related Articles

    • CL2200 - Surface Deadbolt Installation Instructions

      Installation Instructions for the CL2200 Surface Deadbolt Contents     CL2200 1 Front plate 2 Back plate 3 Neoprene seals x 2 4 Spring loaded spindle 5 Mortice Keeper 6 Surface keeper and packing pieces 7 Wood screws x 2 (to use with keeper) 8 Fixing ...
    • CL100/CL200 - 2018 Surface Deadbolt Installation Instructions

      CONTENTS CL100 CL200 1 Front Plate (Key override option shown) 2 Back plate (bolt is packed separately) 3 Neoprene seals x 2 4 Packaging pieces x 2 5 Spring loaded spindle 6 Mortice keeper 7 Surface keeper 8 Surface keeper packing pieces x 1 9 Wood ...
    • CL100/CL200 - 2018 Surface Deadbolt Installation Instructions

      CONTENTS CL100 CL200 1 Front Plate (Key override option shown) 2 Back plate (bolt is packed separately) 3 Neoprene seals x 2 4 Packaging pieces x 2 5 Spring loaded spindle 6 Mortice keeper 7 Surface keeper 8 Surface keeper packing pieces x 1 9 Wood ...
    • KitLock Slam Latch - Installation Instructions

      Suitable for use with the KitLock KL1000 family: KL1000 Classic, KL1000 Classic+, KL1000 G3, KL1000 G3 NetCode, KL1000 NetCode, KL1000 RFID. SPECIAL NOTE The maximum door thickness when using the Slam Latch is 20mm (3/4”). Before installation, ...
    • CL2210 - Mortice Deadbolt Installation Instructions

      Installation Instructions for the CL2210 Mortice Deadbolt   Contents     CL2210 1 Front plate 2 Back plate 3 Neoprene seals x 2 4 Spring loaded spindle 5 Deadbolt 60mm and 70mm, (2  3⁄8" - 2 3⁄4") backset   6 Keeper plate 7 Wood screws x 4 use with ...